The majority of the people prefer using car models rather than other vehicles such as trucks as they suit one’s preferences perfectly. Sometimes while driving, you may experience some noise coming from the dashboard. The noise may increase with time if you ignore it, and in most cases, it needs immediate attention. Some common causes of the issue include; faulty heater control, stepper motor, among others.
The clinking noise in the dashboard is a common issue affecting many car users. If you are one of the people experiencing dashboard noise, don’t worry about it because there are ways in which you can bring your dashboard to function. To begin with, identify the main cause of the issue and try resolving the issue depending on the main cause of the issue. But, if the issue persists, seek professional assistance.
Fortunately, the article below shows the main reasons why the car dashboard may keep making noise. Also, you can follow some essential steps to bring your dashboard to correct functioning. Also, there are some FAQs concerning the car dashboard noise. Kindly read the article below and follow the steps carefully to fix your car to function correctly.
Common reasons why the car dashboard may produce clicking noise
Various factors result in clicking noise, and some require a professional mechanic. The main thing is to fully know all parts of the car and understand how they are functioning correctly. It will make it easier for you to solve the issue, and here are some of the causes.
1. Heater control failing to function
The heater control is essential in regulating the air passing into and out of the car, and it cannot work without some thermostat sensors. Sometimes, the heater control may not be correctly aligned, forcing the engine to start. Once the engine starts, it emits some noise in the dashboard showing the heater control requires calibration to fix the noise.
2. A faulty stepper motor
A stepper motor is an essential part that aids in the car functioning correctly, and sometimes, it may be distorted, resulting in the emission of loud noise in the dashboard. Many of the stepper motors are the main reason why your car keeps making noise once they become faulty. Once you experience such, it is important to fix the motor immediately.
3. A bad relay
The relay is a component within the car responsible for regulating the circuit since a minimum amp circuit is necessary for controlling a heavy circuit, and some of the circuits include; lights, starting motor, among others.
In most cases, the power supply magnet usually moves from the power supply source to the engine forcing the dashboard to emit noise. Also, the dirt composition on the joint points can make the dashboard emit a very loud noise, especially if it keeps connecting and disconnecting at a high rate when connected to the power source several times.
steps to fix the clicking noise in the car dashboard
If you want to solve the issue, you must first identify the main cause.
Tools necessary:
Before starting the process, it is important to have all the materials you need, and they include;
- New relay and other replacement parts.
- Protective gloves.
- A screwdriver.
- Wrench, among others.
Step 1: Identify the main cause of the issue
First, find a reason why the car keeps making a clicking noise. See if the issue is a bad stepper motor, relay, or alternator. After finding the root cause of the issue, proceed to the next step of solving the issue.
Step 2: Troubleshoot the faulty relay
A completely broken or worn-out replay is difficult to repair or troubleshoot. And in such circumstances, you will need to replace it with a new one functioning correctly.
Step 3: Check the condition of the stepper motor
Proceed to check the condition of the stepper motor if the issue persists after replacing the relay. The following steps will guide you;
- First, dismantle the pigtail connector.
- Remove the bad stepper from its location and change it to the new one you’ve calibrated.
- Check if you have done the installation successfully and if not, repeat the process above carefully.
Step 4: Fix a faulty heater control by replacing it with a calibrated one
Heater control requires some calibration to be in good condition. If the heater control is not functioning correctly or is beyond repair, replacing it with a new one might be the only solution. Ensure you use one that suits the car perfectly.
Step 5: Seek help
If the issue persists after carrying out the processes above, please seek help. You may consider calling the original manufacturer for more information or sending an expert to help you troubleshoot the issue. Also, you can contact the nearest mechanic shop to help you fix the issue immediately.
Steps on how to calibrate a heater control
Follow the steps below to calibrate the heat control in your car.
i. Switch off the car’s ignition and the automatic transmission.
ii. Disengage the key from the ignition state.
iii. Give the car some time, approximately 2 minutes after disengaging the car fuse from the HVAC system.
iv. Change the fuse and switch the key in the ignition state and leave it for some time, approximately three minutes, to run without trying to stop it or touching the key.
v. Leave the ignition for a few seconds after you shut it off.
vi. Check if you have calibrated the heater control successfully and then start the engine.
Step by step guide on how to replace car relays
Follow the instructions below to repair your relay.
i. First, check the condition of the relay pins, especially their alignment. If they are misaligned, remove them and reinstall them in the correct location till they match correctly.
ii. If the relay is worn out, dismantle it from its position carefully after wearing gloves to protect your hands from any form of damage.
iii. Gently, place the new relay in its correct location and ensure it fits perfectly and tightens it.
iv. Reinstall all other parts carefully, and don’t forget to refer to the manufacturer’s instructions.
Another type of noise in a car apart from clicking noise in the dashboard
- Rattling noises, which are caused by loose elements in the system
- Screaming noises.
- Ticking noises.
- Humming noises are examples of noises.
Some of the noises are normal, and hearing them indicates that the system is working; however, you must address an issue to lessen the noises when they become louder. Please refer to the manufacturer’s guidelines while solving the noise issues.
Frequently asked questions
- How can I replace the stepper motor of my car?
Follow the steps below carefully to get the best results.
i. Turn off the ignition.
ii. Remove the pigtail connection from the pigtail.
iii. Remove all of the bolts from the system.
iv. Remove the ratchet and socket from the assembly.
v. Replace the stepper motor.
vi. Start the engine by turning on the ignition.
Conclusion
A faulty dashboard may result in the car failing to function as usual and emitting loud noise that may cause a lot of distractions. Some of the causes are in the article above and the steps that will guide you to fix the dashboard issue. Don’t forget to refer to the manufacturer’s booklet.
Lastly, there are some precautions you will need to follow while using your car. First, ensure you service it often, and you may seek additional information from a mechanic. Don’t leave it idle for so long to keep the battery in a good state, and finally, don’t forget to seek help if you have issues exceeding your knowledge.
Related Post:
- Car ac compressor making noise-fix it now
- Car ac making a hissing noise and not cooling
- Car makes gurgling noise when accelerating-fix it
- Car making humming noise at 40 mph
